Which Delhi venues do you work at?

Bharat Mandapam (Around 7,000 in the plenary hall with multiple halls across the ITPO complex); Yashobhoomi (Around 11,000 in the main auditorium plus very large convention and exhibition halls); JLN Stadium (Around 60,000 in the bowl, with the infield used for staged events). Everything goes through the ITPO process — gate passes, approved-vendor paperwork and security screening of every case — so the build calendar has to start 72 hours before a build that would take one night anywhere else. We also cover hotels, farmhouses and open grounds across Connaught Place, Aerocity, Chattarpur, Vasant Kunj, Dwarka, Saket.

How much power does an LED wall draw?

Roughly 150 to 350 watts per square metre on average content, with peaks well above that on full white. Distribution must be sized for peak rather than average, phases balanced across the grid, otherwise the first full-white frame of your opening title trips a breaker.

How do I choose the right pixel pitch?

Start from how close the nearest person stands. As a working rule the viewing distance in metres at which an image resolves cleanly is roughly the pixel pitch in millimetres, so P2.6 reads from under three metres and P4.8 wants five or more. Then check the content: live text and close camera work need finer pitch than colour and motion graphics.

Why does my LED wall look striped on camera?

Because panel refresh rate and camera shutter are not synchronised. Running panels at 3,840 Hz or higher removes most of it, and Brompton processing with ShutterSync plus genlock locks the wall to the camera chain. It must be verified through the actual cameras, because what the eye sees is no guide at all.

How bright does an outdoor wall need to be?

For daylight-visible content, 5,000 nits and upwards, with 7,500 nits comfortable in direct sun. Indoor walls at 800 to 1,500 nits are far too dim outdoors, and brightness is not something processing can fix — it is a panel specification you choose at booking.

Visual · Delhi, Delhi NCR

LED Wall Rental in Delhi

The gap between adequate and excellent LED wall rental in Delhi is usually preparation: ndmc, bses and tata power supply in lutyens, aerocity and dwarka is strong enough to run a conference on house power. the farmhouse belt is the opposite: chattarpur and mehrauli events are dg-primary, typically a synchronised pair of 250 kva silent sets with auto-changeover. the complication unique to delhi is grap — once the commission for air quality management escalates to the higher stages in winter, diesel generator use is curtailed unless the set is retrofitted or dual-fuel, so a december outdoor show needs its power strategy approved before the stage design is signed, and a recce that finds the venue's real constraints before quote stage.

WhatsApp a producer

Rated 4.9/5 by 600+ event planners and brands

Lead time: From 5 weeks
Peak season: Oct–Mar
Coverage: Delhi & Delhi NCR

Key takeaway

LED Wall Rental in Delhi is quoted against your guest count, venue and run of show. The deepest supplier pool in the country sits here, which makes Delhi the cheapest place in India to hire kit — a comparable conference rig quotes well below its Mumbai equivalent — and clients negotiate accordingly. The margin lives in engineering, crew quality and compliance paperwork, not in equipment day rates. India International Trade Fair at Pragati Maidan through the second half of November absorbs every truss section, rigger and forklift in the NCR. Republic Day locks central Delhi for most of January with rehearsal closures from early in the month, state visits close roads without notice, Diwali week empties the labour pool, and the November-December and February muhurat clusters book out the farmhouse belt a year ahead — so we quote within 24 hours and hold dates first-come.

LED Wall Rental for Delhi’s biggest events

Creative LED is a maths problem before it is a visual one. Pixel pitch sets the minimum comfortable viewing distance — as a working rule, the distance in metres at which the image resolves cleanly is roughly the pitch in millimetres, so a P3.9 panel reads well from about four metres and a P2.6 from under three. We choose pitch from where the nearest audience actually stands and from what the content is: a logo-and-colour backdrop forgives a coarser pitch than live text or a camera that will push in on the surface. The panel grid is then drawn to native resolution so content is authored pixel-for-pixel rather than scaled.

Scenic LED is shaped around the room — ceiling trim, sightlines and the position of the nearest seat decide pitch, geometry and whether the build flies or stacks. In Delhi that plays out at venues like Bharat Mandapam, Yashobhoomi, JLN Stadium, and across Connaught Place, Aerocity, Chattarpur, Vasant Kunj.

Processing decides whether the wall looks like a screen or like a surface. Novastar MCTRL4K and Brompton Tessera SX40 handle large canvases, and the Brompton path adds the tools that matter for cameras: high refresh rates, ShutterSync to lock panel refresh to the camera shutter, and genlock so the wall and the broadcast chain share a clock. Without that, a wall sitting at a low refresh rate will show rolling bands and tearing on every camera cut even though it looks perfect to the eye. Indoor walls typically run 800 to 1,500 nits; outdoor daylight surfaces need 5,000 nits and upwards to hold an image against sun.

What’s included

P1.9 to P4.8 pixel pitch
Curved, corner, floor & ceiling LED
Novastar & Brompton processing
Ground-stack or flown

Equipment we carry

AbsenROE VisualUniluminNovastarBrompton TechnologydisguiseResolumeBarco

Why Delhi chooses Prime AV

Crews and trucks positioned for fast load-in at Chattarpur farmhouse venues and venues in Dwarka and Saket.
Pitch is chosen from the real nearest-audience distance, and where seating cannot move we specify a finer pitch for the lower sections only.
Spares inventory log and a record of any panel swapped during the run
Working knowledge of Delhi NCR venue rules, power sanctions and permission timelines.

Local conditions

Producing LED wall rental in Delhi

Weather & the rig

LED panels are the first thing a climate punishes — humidity creeps into ribbon cables, direct sun washes out anything under 5,000 nits, and wind load on a flown wall rises fast with height and surface area. Two distinct problems bracket the season. From mid-December through January, radiation fog drops visibility under 100m and turns projection milky at any useful throw, while 3–5°C call times slow LCD response on monitors and stress LED driver boards before the first cue. Then from late October the post-harvest smoke layer pushes AQI past 400, which hazes beams attractively to the eye and reads as dirty grey on camera, so broadcast-led shows have to light for the haze rather than through it. May and June bring 45°C and loo winds that load filters within a session. Jul–Sep monsoon, where the real hazard is not rainfall volume but the short violent pre-rain squall that arrives in ten minutes and takes down an untethered outdoor structure; mid-Dec to late Jan if the design depends on projection throw.

Power & redundancy

A large LED canvas draws several hundred watts per square metre at peak and spikes on white frames, so distribution is sized to the worst content frame rather than to an average. NDMC, BSES and Tata Power supply in Lutyens, Aerocity and Dwarka is strong enough to run a conference on house power. The farmhouse belt is the opposite: Chattarpur and Mehrauli events are DG-primary, typically a synchronised pair of 250 kVA silent sets with auto-changeover. The complication unique to Delhi is GRAP — once the Commission for Air Quality Management escalates to the higher stages in winter, diesel generator use is curtailed unless the set is retrofitted or dual-fuel, so a December outdoor show needs its power strategy approved before the stage design is signed.

Permits & noise rules

Flown scenic LED needs structural sign-off on point loads, and outdoor builds attract both wind-load scrutiny and, near residential frontage, light-spill objections. Amplified sound and temporary-structure NOCs route through the Delhi Police Licensing Branch, with ground permission from MCD, NDMC or DDA depending on whose land it is, and a Delhi Fire Service NOC for any pandal or raised structure. DPCC applies the noise rules and the 10pm loudspeaker cut-off. Drone operation is close to impossible on a normal timeline: most of the city falls inside the IGI red zone or a VVIP restriction, and anything beyond that needs clearance that goes well past a Digital Sky permission.

Load-in & access

Panel cases are heavy, numerous and must arrive in build order, so dock height, lift capacity and the available load-in window set how much surface can realistically go up. Goods-vehicle restrictions keep trucks out of much of the city through the day, so inventory moves from Okhla, Noida or Gurugram warehousing after 11pm. Pragati Maidan is easier since the tunnel opened, but ITPO gate passes have to be lodged days ahead. Yashobhoomi has purpose-built docks. The genuine trap is the farmhouse circuit, where a single narrow gate is shared with guest arrival, so load-in must be finished and the gate cleared before the first car turns in.

Season & booking

India International Trade Fair at Pragati Maidan through the second half of November absorbs every truss section, rigger and forklift in the NCR. Republic Day locks central Delhi for most of January with rehearsal closures from early in the month, state visits close roads without notice, Diwali week empties the labour pool, and the November-December and February muhurat clusters book out the farmhouse belt a year ahead. Peak demand runs Oct–Mar.

Crew & dispatch

Own NCR base with warehousing across Okhla, Noida and Gurugram, which also makes Delhi the dispatch origin for Jaipur, Agra, Lucknow, Gwalior, Ludhiana and Amritsar. Load-in support covers Dwarka, Saket and the rest of the city.

What it costs here

The deepest supplier pool in the country sits here, which makes Delhi the cheapest place in India to hire kit — a comparable conference rig quotes well below its Mumbai equivalent — and clients negotiate accordingly. The margin lives in engineering, crew quality and compliance paperwork, not in equipment day rates.

Local expectations

Protocol is the deliverable at government and diplomatic events: dais seating order, the lamp-lighting sequence, anthem cues, correct honorifics in the script and a VIP arrival time that will move by forty minutes without warning. Bilingual Hindi and English scripting is assumed, as is a clean press feed. Punjabi weddings here expect high SPL and a finish past the curfew, which is why experienced producers push those clients towards acoustically contained indoor venues rather than fighting the enforcement.

Specification

LED Wall Rental: technical specification

Typical LED wall rental specification supplied in Delhi.
Specification	Detail
Pixel pitch range	P1.9 – P4.8 indoor, P4.8 – P10 outdoor
Viewing distance rule	Minimum comfortable distance in metres ≈ pixel pitch in mm
Brightness	800 – 1,500 nits indoor, 5,000 – 7,500 nits outdoor daylight
Panel refresh for camera	3,840 Hz or higher, with ShutterSync and genlock on Brompton
Processing	Novastar MCTRL4K / VX1000, Brompton Tessera SX40 with Hydra calibration
Ingress protection	IP43 indoor cabinets, IP65 front and rear for outdoor builds
Power draw	Approximately 150 – 350 W per square metre average, peaks higher on white
Geometry	Flat, curved, corner, cube, floor-rated, transparent mesh and kinetic builds
Rigging	Flown on certified motors with point-load report, or ground-stacked on goalpost frames
Spares carried	Five per cent spare panels plus receiving cards, PSUs and ribbon cables

Creative geometry is where scenic LED earns its budget. Curved and corner builds, suspended cubes, floor tiles rated for foot traffic, transparent mesh over a set and kinetic panels on winches all come from the same panel families but each changes the rigging and the power plan. A flown wall needs a point-load calculation and a wind-load assessment outdoors, because a solid LED surface is effectively a sail and the load rises steeply with height and area. Cable dressing matters too: data and power loop through panels in a defined order, and a single ribbon cable creeping out of its socket in humidity takes out a column.

Sizing

What size rig does your event actually need?

Scale	Guests	Recommended setup
Panel backdrop	100 – 400	6 m x 3 m at P3.9, ground-stacked, single processor, 18 sq m
Stage width wall	400 – 1,500	10 m x 5 m at P2.6 or P3.9, flown, Brompton with ShutterSync, 50 sq m
Wrapped stage design	1,500 – 5,000	Main plus side panels and a floor section, 120 – 180 sq m, media server playback
Immersive room	200 – 800	Three-wall plus floor at P2.6, edge-matched, 250 sq m, calibrated as one canvas
Festival scenic	10,000+	Outdoor IP65 at P4.8 – P6.9, 300 sq m+, wind-load assessed, redundant power

Scope

LED Wall Rental scope tiers in Delhi

Backdrop Canvas

Conferences and award stages, up to 40 sq m of surface

P2.6 or P3.9 indoor panels on a ground-stacked goalpost
Novastar processing with native-resolution canvas mapping
Content playback with one operator and a hot backup machine
Five per cent spare panels and consumables on site
LED technician plus one rigger for the build

Most booked

Scenic Build

Launches, concerts and award nights, 50 – 180 sq m with shaped geometry

Curved, corner or multi-surface build with flown sections
Brompton processing with ShutterSync and genlock for cameras
disguise or Resolume media server with timecoded playback
Point-load report and certified rigging
Two LED technicians, a media server operator and a rigging crew

Immersive Surface

Large stage designs and immersive rooms, 200 sq m and above

Multi-plane design with floor LED, cubes and kinetic elements
Redundant processing with hot-standby servers and dual data paths
Full panel calibration pass for colour and brightness uniformity
Content pipeline support with pixel maps issued to your studio
Full-time crew across build, show days and strike

Venues

Where we work in Delhi

Venue	Capacity	Production note
Bharat Mandapam	Around 7,000 in the plenary hall with multiple halls across the ITPO complex	Everything goes through the ITPO process — gate passes, approved-vendor paperwork and security screening of every case — so the build calendar has to start 72 hours before a build that would take one night anywhere else.
Yashobhoomi	Around 11,000 in the main auditorium plus very large convention and exhibition halls	The sheer footprint is the constraint: control positions end up a long way from stage, so fibre and signal distribution rather than copper multicore decides whether the design works.
JLN Stadium	Around 60,000 in the bowl, with the infield used for staged events	SAI holds the approvals, the athletics track and infield need full protection boarding, and the roof carries no event rigging at all, so even a modest stage needs ground-support towers with ballast calculations.
Siri Fort Auditorium	Around 1,200 seated	A fixed proscenium house with house rigging and a locked projection throw, so any design that wants a different screen position has to solve it with ground support in the wings.
Chattarpur farmhouse venues	Typically 1,000–5,000 across lawns and covered structures	Driveways are gravel or kutcha and will not take a loaded trailer without ground-protection boards, and almost every one of them is generated end to end with no usable house feed.

Crew

Who turns up on show day

LED technician
Builds the panel grid, maps the canvas to native resolution and chases any dead panel, card or ribbon on sight.
Media server operator
Runs disguise or Resolume, holds the content timeline against timecode and keeps a hot backup machine mirrored.
Rigger
Flies the sections, checks point loads against the report and manages any kinetic or winch elements.
Video engineer
Owns processing, refresh rate, ShutterSync and genlock so the wall behaves correctly on every camera.
Content technician
Conforms incoming content to the pixel map, fixes aspect and colour issues and version-controls what plays.

What you receive

Pixel map with native canvas resolution, aspect ratio and safe areas
Panel grid drawing with data and power loop order
Point-load report and, outdoors, a wind-load assessment
Processor configuration record including refresh, ShutterSync and genlock settings
Brightness and colour calibration report across the surface
Content playlist with timecode cues and a backup on two drives
Spares inventory log and a record of any panel swapped during the run

Timeline

From enquiry to load-out

T-5 weeks
Pitch and geometry decision
Nearest viewing distance, camera plan and content type set the pixel pitch and the panel grid.
T-4 weeks
Pixel map issue
Your content studio receives the exact canvas resolution, aspect and safe areas so nothing is authored to be scaled.
T-2 weeks
Rigging and power sign-off
Point-load report, wind-load assessment for outdoor builds and the power schedule go to the venue.
Show day −2 to −1
Build and calibration
Panels built, data and power looped, canvas mapped, then a brightness and colour calibration pass across the surface.
Show day −1
Camera check
Refresh, ShutterSync and genlock verified live through the actual cameras, with content on screen.
Show day to +6 hours
Show and strike
Operated through the show with spares on hand, then de-rigged panel by panel into cases in build order.

Risk control

What goes wrong, and how we stop it

What can go wrong

How we prevent it

What can go wrong
The front row sits three metres from a P4.8 panel and sees pixels rather than an image.
How we prevent it
Pitch is chosen from the real nearest-audience distance, and where seating cannot move we specify a finer pitch for the lower sections only.
What can go wrong
Average power is calculated from the spec sheet and the breaker trips on a full-white frame.
How we prevent it
Distribution is sized for peak draw on white content, not average, with phases balanced across the panel grid and content peak-limited where sensible.
What can go wrong
The wall looks flawless to the eye but shows rolling bands on every camera.
How we prevent it
Run panels at 3,840 Hz or higher and lock ShutterSync and genlock to the camera chain, then verify through the actual cameras before the show, not at rehearsal.
What can go wrong
Content authored at 1920 x 1080 is stretched onto a non-standard canvas and every logo distorts.
How we prevent it
The pixel map goes to the content studio at T-4 weeks with exact resolution and safe areas, and we conform and review every file before build day.

Honest comparison

Is this the right choice for your event?

Projection instead of LED for a stage backdrop
Our verdict
Projection is far cheaper per square metre for very large surfaces and looks beautiful on texture. LED wins whenever there is ambient light, a camera, or performers who would walk through a projector beam.
A coarser pixel pitch to save budget
Our verdict
Often the right call. If the nearest viewer is eight metres away and the content is graphics rather than text, P4.8 looks identical to P2.6 at a fraction of the cost. It only fails when a camera pushes in.
Ground-stacking instead of flying the wall
Our verdict
Ground stacks are cheaper, faster and avoid a rigging sign-off. The trade-off is a visible frame, a higher bottom edge and lost stage depth, which matters on a set but not behind a lectern.

Demand

What Delhi books most

Delhi event mix

Government, ministry and multilateral summits
Trade exhibitions and industry association conventions
Large farmhouse and hotel weddings
Corporate conferences, dealer meets and award nights
Product launches and auto reveals
Political rallies and public functions

Ideal for

Events we power with LED wall rental in Delhi

Conferences

Concerts

Award nights

Process

From brief to standing ovation

Brief & recce

We visit the venue, map power and rigging, and understand your show flow.

Design & quote

CAD plans, 3D previews and an itemised quote within 24 hours.

Build & rehearse

Load-in, system tuning, content checks and full technical rehearsal.

Show & strike

Show-caller-led execution, then a quick, clean load-out.

FAQ